Oracle Server S7-2L Power Calculator

Oracle's servers based on the SPARC S7 processor support the revolutionary Software in Silicon technology which enables the real-time enterprise through unprecedented levels of security, efficiency and value. The SPARC S7-based servers are the ideal platforms for databases, Java and application deployments. The rich feature set offers the best value for cloud infrastructure and business-critical enterprise applications.

The SPARC S7-2L server offers two processors, a maximum of 1024GB of memory, six PCIe 3.0 slots and four disk chassis options:

  • Eight-disk chassis: Eight 2.5-inch SAS-3 drives, four drive bays support NVMe
  • Twelve-disk chassis: Twelve 2.5-inch NVMe solid state drives
  • Fourteen-disk chassis: Twelve 3.5-inch SAS-3 hard disk drives and two 2.5-inch SAS-3 drives
  • Twenty six-disk chassis: Twenty-six 2.5-inch SAS-3 drives, four drive bays support NVMe

The intent of the power calculator is to provide guidance for estimating the electrical and heat loads for typical operating conditions. It should not be used to calculate power or HVAC requirements. Instead, please use the appropriate site planning guide to allow for proper allowances.

Notices and Disclaimers
  • Note: JavaScript must be enabled to view this section of the website.
  • Configure your Oracle Server X7-2L and calculate your system's total power consumption.

Configure your Oracle Server S7-2L and calculate your system's total power consumption.


Item Quantity Notes
Processor
Select Processor Type
CPUs
Select Number of CPUs
Memory
(64GB DIMM)
Select number of DIMMs
Memory
(32GB DIMM)
Select number of DIMMs
Memory
(16GB DIMM)
Select number of DIMMS
Disk Chassis
Select the base chassis
Eight 2.5-inch SAS3 drive cage
Twelve 2.5-inch NVMe drive cage
Twelve 3.5-inch SAS3 drive cage and rear two 2.5-inch SAS3 drive cage
Twenty-four 2.5-inch SAS3 drive cage and rear two 2.5-inch SAS3 drive cage
 
Hard Disk Drives (2.5-inch)
Select number of Hard Drives
Hard Disk Drives (3.5-inch)
Select number of Hard Drives
Solid-State Drives (2.5-inch)
Select number of Solid-State Drives
NVMe Drives
Select number of NVMe Drives
PCI-Express Card
Select number of PCI-Express Cards
Indicate Workload (%):
Select Workload range
(1% - 100%)
   
 

Sample Results
Item
Active Idle Power
Sample Power
Total Power of System   (Watts)
(estimated)
(estimated)
Total Power of System   (BTU/HR)
(estimated)
(estimated)
 

Notices and Disclaimers

You MUST allow electrical and cooling headroom for unforeseen circumstances, component upgrades, and increased computational loads. Please allow for worst-case power conditions. Actual power consumption will vary from the sample workload used in the power calculator. These include, but are not limited to, the factors below. Each of these factors may cause significant differences in power consumption:

  • Actual workload and its fluctuations
  • Ambient temperature
  • Cooling patterns
  • Excessive inlet temperature
  • Humidity
  • Operating systems features
  • Power management settings

The "Sample Power" results shown (if using 100% workload) represent server power consumption measurements with CPUs at 100% utilization running SPECjbb2005. HPC workloads may consume more power than the commercial workload used in this calculator. If shown for this calculator, the "Active Idle Power" results represent power consumption measurements taken from servers with operating systems booted and stabilized, yet running at minimal utilization. Sample results shown are representative of measurements taken with room temperatures below 25°C. System power can vary depending upon hardware/software configurations and environmental conditions. For precise results, actual measurements based upon the exact hardware/software/environmental conditions are recommended.

Legal Notice: This calculator is subject to change without notice and is provided "as is" without warranty of any kind, express or implied. Oracle does not make any representations regarding the use, validity, accuracy or reliability of the tool. The entire risk arising out of the use of this tool remains solely with the customer. In no event shall Oracle be liable for any direct, consequential, incidental, special, punitive or other damages, even if Oracle is negligent or has been advised of the possibility of such damages, arising from use of the tool or the information provided herein.